If you have a problem in fixing your washing machine, you don’t have to call a repair person, why don’t you try to fix it yourself? Most problems that happen in your washers are actually quite common and can be easily fixed. There’s really to need to spend unnecessary money to call a repair man to come and fix it.
Before starting to fix a washing machine Washer Repair Los Angeles, make sure the washer is unplugged first. Some people thinks that a small problem could be fixed without unplugging the machine, but even the smallest problem, you must unplug it. This is mainly for safety reasons. Besides, why wouldn’t you unplug it if it takes only a second?
Tips for purchasing parts in repairing a broken washer
Before disposing your old broken washer, keep in mind that your next washing machine would be broken and in time to come, you may need some spare parts to fix it as way. Hence, you may want to check your old broken washing machine before disposal and dismantle the parts you need. Buying from a retailer of washing machine repair is not a good idea, because they would also be buying the used parts of recycled washing machines. A better option is to check with a wholesale appliance parts sellers where you can get brand new and even cheaper washing machine spare parts.
Spinning or Agitating Troubles
If the washing machines agitator won’t work, rest easy. Compared to other parts of the washing machine, agitators are comparatively easier to fix. The drive belt makes the agitator work, and if when this belt becomes loose, it could cause the agitators in washing machine to malfunction. To see the drive belt of the agitator, remove the back panel of the washer. Find the drive belt and press it. If the machine moves about ¾ inch, all you have to do is to tighten it. If you see the belt drive is really damaged, it’s time to buy a new one.
In tightening a drive belt, all you have to do is loosen up a little bit the mounting nut on the motor and ease its motor with the mountain rail. Wait until the belt is perfectly tight and before mounting the nut. Final step is to return the access panel and your washer will be fixed.
Leaking washing machine
If you have a leaky washer, and it’s highly probable that the leak is coming from the hose. To solve such washing machine problems, monitor the hoses while the washer is filling. If you locate where the leak comes from, all you got to do is tighten the hose.
Snags or Rips in Material
If you see snags or rips inside the washing machine, it could be coming from the tub or agitator. Some washers tub is made up of plastic and it’s materials is fairly rust resistance. Unfortunately, the holes in these tubs could rust. If you want to check whether there are any rough spots inside your tub, simply place an old nylon to stuck over your hand and go over the tub. If there is a spot that snags your clothes while washing, then you will locate the stocking. You could easily fix this up with sandpaper and sand it down.
Replacing the Agitator
If your agitator is broken, you have to find a replacement as soon as possible. Delaying it could destroy your clothes. In replacing an agitator, simply remove the dispenser that covers the agitator and remove the screw under it. After this, just lift the agitator out. If it is hard to be pulled out, fill the washer with hot water to remove any soaps or anything that holds it down. If that won’t work, hit softly the agitator with a rubber mallet on order to loosen it. When the agitator is removed, you can replace it with a new one.
Washing Machine Won’t Fill
Each time you notice your washer won’t fill with water, the filter screen could be clogged from the hot or cold passage hose. To fix this, just switch off the cold and hot water faucets and remove the hose by unscrewing it. Check if the filter screen is dirty and clean it. You should also check if the hoses are cutting the water supply flowing to the washer.
Clothes are Too Wet After Spin Cycle
If you notice that after you spin cycle, the clothes are still wet, it’s advisable to inspect your drainage hose for faults. It could be kinked or clogged. Check the hose and clean it up using long-handled brush. You could purchase one of these long-handled brushes in aquatic or pet stores. You could also use the brushes that are used for cleaning the aquarium tubes. If the problem is hose kink, just remove it. If it is stocked pretty tight, you would probably have to replace a new one. Now you could use your washing machine perfectly!